Replacing uPVC Window Handles
The replacement of window handles made of upvc is a simple task. It is essential to ensure that the replacement handle fits inside the spindle cutouts in the window mechanism.
If the steps listed below are followed correctly, any cockspur handle should fit most windows. The most important thing is the step height of the handle.
What to Look For
As time passes, uPVC handles on many windows in the UK can start to show signs wear and wear and tear. The handle of the window may become loose or difficult to operate when this happens. This is a fairly easy task that is achievable by anyone who is comfortable using basic hand tools.
The first step is to make sure that the handle is securely fixed to the frame of the window and in its open position. The next step is to find the screws or pins that secure the handle in place. These are usually located on the inside of the handle. They can be removed with a screwdriver and pliers.
When the handle is loose it can be taken from its hinges by gently pulling off. Then, you will need to locate a new handle in the same dimensions and style. This can be done online or in an area DIY store, and the process should only take around five minutes using a screwdriver.
The most important thing to consider when replacing a uPVC window handle is its step height. This is the distance from the bottom of the handle to where it rests on the frame of the window. This is a typical measurement, and you should verify the height of the step before purchasing the replacement handle.
There are a variety of sizes based on the type of handle. Inline handles for uPVC windows typically feature lug centers of 31mm There are also varieties of cockspur handles that have 43mm centres. Tilt and turn handles are typically found on uPVC windows, and they feature a specific design that allows the window to be slid up for ventilation, and then rotated to fully open the window.
The most frequent breakage in uPVC handles is that they crack inside instead of breaking away from the base section. repairmywindowsanddoors can make them hard to open and is why it is essential to ensure that the replacement handle you purchase has the same length of spindle as the one you have.
Remove the old handle
If your window handles are damaged or incorrectly fitted, they could cause double-glazed windows to not open or close correctly. They could even become stuck. This could be due to various reasons, including general wear and tear on the metal handle or corrosion. In these cases, it is important to locate replacement window handles made of upvc as soon as possible in order to avoid further damage and loss of function.
When replacing the handles on windows made of upvc and handles, it is important to remove the old handles from the window. To do this, begin by taking off the screw that is encased when the handle is in a closed position. After you have removed the screw, you can take off the handle. It is possible to make the task easier by using an electric screwdriver.
It is also important to be aware that screws can be hidden under caps made of plastic. It is recommended to remove the covers with a Stanley knife. After the handle has been removed, you must examine the square cut out on the handle's base to ensure that the new window lock handles will work with it. This is crucial as you'll need to determine the length of the spindle on the previous handle to ensure that it is the same size as the window mechanism and handle spindle cut out.
There are three types of upvc handles: Espag handles with a central screw that can be turned right or left, Cranked handles with two screws and Spade handles that have arms that are flat and can be used on either side of the window made of upvc. When you have a suitable replacement, it is simple to screw the handle into position and ensuring that the spindle is correctly fitted into the lock mechanism. After that, you can then tighten the handle to the window frame. Your replacement upvc handles should now be secured.
Measure the Spindle
If you're looking to replace a upvc handle that has collapsed, it's likely the spindle that holds it in place is damaged or loose. In some instances, it can be fixed using a screw or pin to secure it. In some cases it might be necessary to replace the handle. There are a variety of handles made of upvc. There are three types of handles: inline espagnolette, cockspur, and tilt-and-turn. Each type of handle is mounted and replaced in a different fashion.
It is crucial to measure the handle before buying the replacement. This will ensure that the new handle is the correct size and will fit correctly within the window. All handles are calibrated according to industry standards, making it easy to determine the right size.
To measure the size of your handle first, take it out of the window by turning it to an open position. You should then be able to see the size of the screw or pin that secures it. Use a ruler or a tape measure to determine how long the spindle is. Once you know the length of the spindle you can purchase a replacement one with exactly the same size.
When you are looking to replace a handle, it is important to take into consideration the step height of an upvc window handle. The step height is measured from the base to the point at which the handle is positioned on the frame. Typically, this will be approximately 21mm for uPVC windows, and 9mm for aluminium. Dropping something in the gap will allow you to determine how far the handle extends before it meets an obstruction.
Cockspur handles usually have different backset heights depending on the type of window they're installed in. Inline Espag handles come with the standard height of 43mm from centre to centre (2 fixing points). Cockspur handles have different backsets depending on the type of window they are located in. This is because they feature an extension spur that extends from the handle and is secured over a cockspur wedge striker plate.
Fit the New Handle
Once you've selected the new handle, ensure that it is aligned with the screw holes on the door. Secure it using the screws supplied. Install the latch lever the same manner as the handle that you are replacing if you are also replacing the door handle. Then, you can attach the door trim once more to conceal the screws for mounting.
Tip: To remove a metal head from a wedge made of wood, place the handle on the floor, so that its wide end is on the ground. Then, you can use a hammer and tap the narrow end. Be careful not to damage the handle or the spindle.